Hunter 3 Speed Fan Switch Wiring Diagram

May 22, 2024 Post a Comment

Hunter 3 speed fan switch wiring diagram

1: black from capacitor. 2: yellow from capacitor (6µF, 200V) 3: red from capacitor (3.5µF, 200V)

How do I replace the pull switch on a 3-speed ceiling fan?

How to Replace a 3-Speed Ceiling Fan Chain Pull Switch

Turn Off the Power. Shut down power to the fan.
Set Up a Ladder. Climb a ladder or step-up to reach the fan housing. ...
Remove the Cover Plate. ...
Loosen the Fan Housing's Nut. ...
Take Pictures of the Wires. ...
Disconnect the Wires. ...
Match the Part. ...
Install the New Switch.

What is the blue wire on a Hunter ceiling fan?

Blue wire is for the light, if light is included with the fan. White wire is neutral. Green wire is for the ground. Red wire is sometimes included and acts as a conductor to carry power to the light kit.

What is the black and white wire on a Hunter ceiling fan?

The black wire is the hot wire that leads to the switch. The white wire is neutral and completes the electrical circuit. Copper or green wire is the ground wire and keeps the fan from experience power surges.

What color wire is hot on a 3-way switch?

Wiring for a 3-Way Switch The most important wire to get right is the one connected to each switch's common screw terminal. This is the "hot" wire (usually colored black, but not always), and it brings the power from the source and delivers it to the first switch and then from the second switch to the light fixture.

How do you tell which wire is which in a 3-way switch?

If no house current is found on any of the three wires. Go to the other switch. And do the same

How do you wire a ceiling fan with a 3 way switch?

For individual control of the fan and light, connect black wire to ceiling fan black wire and connect the red wire to ceiling fan blue wire. Secure all the connections with orange wire nuts. Then, neatly place all wires into the ceiling box and secure the covers for the fan.

How does 3-speed fan switch work?

With 3-speed motor, Hot voltage connects to main winding at 3 different points. Only 1 point at a time receives power. That's what the fan switch does. When voltage is applied to each point, the main winding is energized as voltage from Black Hot wire completes circuit with White neutral wire.

What does L 1 2 3 mean on a ceiling fan switch?

Position: OFF, High speed=L-1, Medium speed=L-2, Low speed=L-3.

Where does the blue wire go on a Hunter fan?

The blue wire from the ceiling fan gets connected to the second live wire from the ceiling. This second wire can vary in color but is most commonly red or black. This connection allows you to power your lights from the second switch. Connect the white grounded wire from the ceiling to the white wire from the fan.

Does the blue wire go to black or white?

If you do have a fixture using international standards, the good news is that the matching is very easy. Brown is your hot wire so you want to connect that to your building's black wire. The blue is negative or return, so that will go to white.

What color wires go together?

The protective ground is green or green with yellow stripe. The neutral is white, the hot (live or active) single phase wires are black , and red in the case of a second active.

Do red and black wires go together ceiling fan?

If you have black and red wires in the ceiling fan power box, the are likely from the same branch circuit source, one black wire in the wall switch box, and then black and red from the double switch to the fan ceiling box. This way you can run the fan and the fan light kit separately. Don't connect them together.

What is the red wire on a Hunter ceiling fan?

A red wire up in the ceiling fan junction box usually indicates that the wiring has been installed which provides separate switch for the light and a separate switch for the fan motor. If your ceiling fan does not have a light fixture, then simply cap off the red wire and attach the fan motor to the black wire.

What do I connect the black and white wire to?

Power comes from the service panel along the black (hot) wire through other outlets, switches and light fixtures on the circuit and begins its return to the source through the white (neutral) wire. The black wire attaches to a brass terminal; the white wire, to a silver terminal.

What happens when a 3 way switch is wired wrong?

Usually when a 3-way switch fails, lights can be toggled on and off at one switch, but not the other. If one of the two 3-way switches toggles the light(s) on and off, the other 3-way switch has probably failed.

Which terminal is hot on a 3 way switch?

The black "hot" wire enters the switch on the left. Three-way wire(which includes red, black and white wires) runs from the switch on the left to the switch on the right, with the white wire carrying ground and the red and black wires carrying the output from terminals in the left switch.

Which wire is hot on a 3 wire?

The black wire is the hot wire. It becomes energized as soon as you insert the plug into a working receptacle. The white wire is known as the neutral or return wire.

What Colours are the 3 wires?

U.S. Electrical Wiring Color Codes

Phase 1 - Black.
Phase 2 - Red.
Phase 3 - Blue.
Neutral - White.
Ground - Green, Green with Yellow Stripe, or Bare Wire.

What are the different terminals on a 3-way switch?

A 3-way switch is larger than a single pole switch and has three screw terminals for wiring connections, plus a ground. Two of these take traveler wires that go from one switch to the other. For the third terminal, one switch is connected to the hot supply wire while the other switch is joined to the light.